| Basic operating principle | A hinged disc swings open with forward flow and returns toward the seat when flow reverses. | A piston, disc, or poppet moves vertically away from and back onto a seat. | Two spring-assisted plates open into the flow path and close when forward flow decreases or reverses. | A guided disc or plug moves axially along the pipe centerline, usually with spring assistance. |
| Flow direction | One-way flow; the valve must be installed according to the body flow arrow. | One-way flow; the pressure differential must lift the closure member from its seat. | One-way flow; the two plates respond independently to changing flow conditions. | One-way flow; the streamlined closure member follows the pipe axis. |
| Typical pressure-drop tendency | Low to moderate when fully open; the hinged disc remains in the flow path. | Moderate to high compared with full-flow designs because the closure member moves through a guided seat area. | Low to moderate; the short face-to-face design can reduce system space and flow resistance. | Generally low when properly sized because the flow path is streamlined and centered. |
| Water-hammer behavior | Can produce significant slam in high-velocity or rapidly reversing systems, especially with a long disc travel path. | May slam if the closure member is heavy or the valve is installed in an unsuitable orientation. | Usually offers improved non-slam performance because the plates have short travel and spring-assisted closing. | Typically provides fast, low-shock closure when the spring and sizing are correctly selected. |
| Preferred installation orientation | Horizontal installation is commonly preferred. Vertical upward-flow installation may be permitted by the design. | Often installed in horizontal lines or vertical lines with upward flow, subject to the valve design. | Can often be installed horizontally or vertically, but the supplier must confirm orientation limits and spring configuration. | Frequently suitable for horizontal or vertical piping because the closure is guided along the centerline. |
| Space requirement | Usually longer face-to-face dimensions than wafer-style designs. | Generally compact, but the bonnet or cover requires access for inspection and maintenance. | Very compact and lightweight in wafer or lug configurations, reducing installation space and support loads. | Compact body design with relatively short face-to-face dimensions in many applications. |
| Main advantages | Simple construction, broad size availability, relatively low purchase cost, and suitability for many liquid services. | Good shutoff potential, controlled closure movement, and suitability for clean liquid or gas applications. | Short face-to-face length, low weight, fast response, and good resistance to reverse-flow shock. | Low pressure loss, fast dynamic response, compact construction, and good suitability for high-flow systems. |
| Main limitations | Potential disc slam, sensitivity to flow pulsation, and possible wear at the hinge or seat. | Higher pressure loss, possible sensitivity to dirt, and orientation restrictions for some models. | Spring and plate components require correct material selection; some designs are less suitable for solids or severe fouling. | More complex internal guidance and spring components can increase cost and maintenance requirements. |
| Typical applications | Water and wastewater lines, pump discharge piping, cooling-water systems, process pipelines, and general industrial service. | Boiler feedwater, compressor discharge, refinery and chemical process lines, and applications requiring controlled seating. | HVAC systems, water treatment, fire-protection piping, pump systems, and space-constrained industrial pipelines. | Gas transmission, compressor stations, chemical processing, power systems, and high-flow industrial services. |
| Common material choices | Carbon steel, ductile iron, cast iron, stainless steel, and corrosion-resistant alloys. | Carbon steel, stainless steel, alloy steel, and other materials selected for temperature and fluid compatibility. | Carbon steel, stainless steel, ductile iron, aluminum-bronze, and engineered seating materials. | Carbon steel, stainless steel, alloy steel, and specialized alloys for corrosive or high-temperature services. |
| Key buyer checks | Confirm allowable installation angle, disc travel, minimum flow velocity, seat material, pressure rating, and reverse-flow performance. | Confirm minimum lift pressure, orientation, guide clearance, seat leakage class, temperature rating, and clean-service suitability. | Confirm wafer or lug pattern, spring material, minimum operating pressure, plate clearance, leakage requirements, and line support needs. | Confirm flow coefficient, cracking pressure, spring response, body length, noise or vibration limits, and pigging requirements. |
| Relevant procurement documents | Dimensional drawing, pressure-temperature rating, materials certificate, pressure-test report, installation instructions, and spare-parts list. | Certified drawing, material traceability, seat-leakage test results, pressure-test report, maintenance instructions, and coating details. | Wafer or lug dimensions, spring and plate material certificates, functional test data, leakage results, and installation clearances. | Flow-performance data, spring test results, pressure-temperature rating, material certificates, noise data, and inspection documentation. |
08045479132
Send Inquiry
Send Inquiry
Send SMS
