| EPDM rubber | Suitable to evaluate for outdoor weathering, ozone exposure, and hot-water or steam service; generally not selected for petroleum-oil exposure without specific validation. | Specify the operating temperature, media, hardness (Shore A), tensile strength, elongation, compression set, and ozone/weathering requirements. Many grades are used across approximately −40 to +120°C; confirm the grade-specific limit. | Identify any applicable drinking-water, food-contact, or other market-specific requirements. Request the exact compound formulation designation and supporting declarations where required. | Request a current technical data sheet, lot-specific certificate of analysis, and test results for the agreed properties. Validate with samples under the actual media, temperature, and exposure conditions. |
| NBR rubber | Commonly considered for seals exposed to oils and fuels; suitability depends on the fluid composition, temperature, and acrylonitrile content of the grade. | Specify fluid compatibility, temperature range, hardness, tensile strength, elongation, and compression set. Many grades are used around −30 to +100°C, but formulation and exposure can change performance. | State restrictions on substances and any required market or end-use declarations. Request material identification and traceability for the supplied compound. | Ask for documented oil-swell or fluid-compatibility data using a named test fluid and test conditions. Confirm dimensions and sealing performance on production-representative parts. |
| Silicone rubber | Often evaluated for wide-temperature applications and electrical insulation; specify whether the part requires low-temperature flexibility, outdoor resistance, or food-contact suitability. | Define temperature exposure, hardness, tensile strength, tear strength, compression set, color, and any electrical properties. Some grades operate over a broad range, commonly around −50 to +200°C; confirm continuous-use limits for the selected grade. | For food-contact uses, identify the applicable jurisdiction and product conditions. A general material description alone does not establish compliance for a finished article. | Request grade-specific technical data, applicable declarations, batch identification, and test reports. Assess odor, extractables, and finished-part performance where relevant to the application. |
| FKM rubber | Consider for demanding heat and chemical exposure, especially where the specific fluid compatibility is established; not all grades suit every chemical or low-temperature condition. | Specify the exact media, temperature profile, hardness, compression set, and swelling limits. Many grades are used around −20 to +200°C, with limits varying by formulation and exposure. | Document restricted-substance requirements and end-use approvals, if applicable. Require clear identification of the supplied grade rather than relying only on a generic polymer name. | Request compatibility data for the actual fluid and temperature, lot traceability, and a certificate of analysis against agreed limits. Test seals in the intended assembly where failure risk is significant. |
| HDPE plastic | Commonly considered for chemical containers, pipes, and other applications requiring a relatively low-density polyethylene; confirm stress, temperature, and chemical conditions. | Specify grade, density, melt-flow rate, tensile properties, impact requirements, dimensions, and service conditions. Typical HDPE density is approximately 0.94–0.97 g/cm³; mechanical properties depend on grade and test method. | For food contact or regulated uses, specify the target market, applicable rules, and intended conditions of use. Request declarations for the exact grade and, where needed, the finished article. | Request a technical data sheet, batch certificate, resin identification, and process-control records. Verify dimensions, impact performance, and chemical resistance using defined test methods. |
| Polypropylene (PP) | Often evaluated for lightweight molded parts and chemical-resistant components; distinguish homopolymer and copolymer grades because impact and stiffness differ. | Specify polymer type, melt-flow rate, stiffness, impact strength, heat exposure, shrinkage, and dimensional tolerances. Typical PP density is approximately 0.90–0.91 g/cm³, subject to grade and additives. | Identify any applicable food-contact, restricted-substance, or product-specific requirements. Confirm that declarations match the exact grade, color, and additive package. | Request grade-specific data and batch traceability. Approve molded samples against fit, function, appearance, and dimensional criteria before production release. |
| PA 6 (nylon 6) | Consider for load-bearing or wear-related components, while accounting for moisture exposure and its effect on dimensions and mechanical behavior. | Specify grade, reinforcement, moisture conditioning, strength, impact, wear, and dimensional tolerances. State the test conditioning method because polyamide properties change with absorbed moisture. | Define applicable substance restrictions and any end-use approvals. Require disclosure of reinforcement, colorants, and other additives relevant to the specification. | Request technical data for the exact conditioned grade, batch documentation, and dimensional inspection results. Evaluate parts after representative moisture and temperature conditioning. |
| PTFE plastic | Often considered for low-friction or chemically demanding components; account for creep under load and verify suitability for wear applications. | Specify temperature, chemical exposure, load, friction, wear, dimensions, and whether a filled grade is required. Many PTFE grades are rated for continuous service near 260°C, but design and grade limits must be verified. | For regulated uses, define the applicable market and conditions of use. Request documentation for the specific grade and any fillers or processing aids. | Request grade identification, property data, and dimensional inspection records. Check creep or wear under representative load, temperature, and operating duration. |
| Supplier quality system and traceability | Define production location, process capability, subcontracted operations, lot size, and continuity requirements before qualification. | Agree on acceptance criteria, sampling plan, change-control process, nonconformance handling, and measurable critical-to-quality characteristics. | Request current quality-system certification where relevant, while recognizing that certification does not by itself certify a product or guarantee its suitability. Specify applicable regulatory declarations separately. | Review sample inspection reports, lot traceability, corrective-action examples, audit findings, and the supplier’s process for notifying customers of material or manufacturing changes. |