| 1 | 8-inch two-way in-ceiling speaker | Large living rooms, conference rooms, and general background music | 8 in woofer with separate tweeter | 50–100 W RMS per speaker | Usually 8 ohms | Approximately 45 Hz–20 kHz | Cutout: 9.5–10.5 in; depth: 4–6 in | 16 AWG for longer runs; 14 AWG for very long runs | Space speakers evenly and aim the tweeters toward the listening area | Check joist clearance and use back boxes where required by local code |
| 2 | 6.5-inch two-way in-ceiling speaker | Bedrooms, offices, kitchens, and medium-sized rooms | 6.5 in woofer with tweeter | 30–75 W RMS per speaker | Usually 8 ohms | Approximately 55 Hz–20 kHz | Cutout: 7.5–8.5 in; depth: 3–5 in | 16 AWG speaker cable is suitable for most residential runs | Place in a symmetrical pair, typically 6–10 ft apart | Use a stud finder and leave clearance from recessed lights, ducts, and plumbing |
| 3 | 6.5-inch stereo-input ceiling speaker | Bathrooms, hallways, small rooms, and single-speaker zones | 6.5 in dual-voice-coil woofer | 20–60 W RMS per speaker | Typically 8 ohms | Approximately 60 Hz–18 kHz | Cutout: 7.5–8.5 in; depth: 3–5 in | Use four-conductor cable to carry left and right channels | Center the speaker in the room when one unit must cover the entire space | Choose a moisture-resistant design for humid locations; do not install directly above a shower |
| 4 | 6.5-inch angled in-ceiling speaker | Home theater surround and focused listening areas | 6.5 in woofer with angled tweeter | 40–80 W RMS per speaker | Usually 8 ohms | Approximately 50 Hz–20 kHz | Cutout: 7.5–8.5 in; depth: 4–6 in | 16 AWG cable; maintain correct polarity throughout the system | Aim the angled driver toward the seating position rather than straight down | Keep left and right channels at equal distances from the main listening position |
| 5 | 8-inch high-output ceiling speaker | Retail areas, open-plan offices, restaurants, and larger spaces | 8 in woofer with high-power tweeter | 75–150 W RMS per speaker | Usually 8 ohms; some support 70/100 V operation | Approximately 45 Hz–19 kHz | Cutout: 9.5–10.5 in; depth: 5–7 in | 12–14 AWG for high-power low-impedance runs; approved fire-rated cable where required | Use multiple speakers at moderate volume instead of overdriving a few units | Confirm amplifier load and ventilation before connecting high-power systems |
| 6 | 70/100-volt commercial ceiling speaker | Schools, offices, hotels, retail spaces, and multi-zone paging | 6.5–8 in full-range driver | 10–30 W selectable transformer taps | 70/100 V distributed audio system | Approximately 70 Hz–18 kHz | Cutout: 8–10 in; depth: 3–6 in | 16 or 18 AWG two-conductor cable is commonly used, subject to code | Arrange a consistent grid for even coverage and intelligible announcements | Use a compatible distribution amplifier and keep total tap wattage below amplifier capacity |
| 7 | Moisture-resistant ceiling speaker | Bathrooms, covered patios, saunas, and coastal properties | 6.5–8 in treated woofer | 30–80 W RMS per speaker | Usually 8 ohms | Approximately 55 Hz–20 kHz | Cutout: 7.5–10.5 in; depth: 3–6 in | Use outdoor-rated or in-wall-rated cable appropriate to the environment | Keep away from direct water spray and provide adequate drainage around the opening | Verify the actual ingress or moisture rating; “moisture-resistant” does not always mean waterproof |
| 8 | Low-profile shallow ceiling speaker | Renovations, apartments, narrow joist cavities, and limited-ceiling-depth projects | 5.25–6.5 in woofer | 25–60 W RMS per speaker | Usually 8 ohms | Approximately 65 Hz–19 kHz | Cutout: 6.5–8.5 in; depth: 2.5–3.5 in | 16–18 AWG cable for typical short residential runs | Use two or more speakers to improve coverage and reduce the need for high volume | Confirm the minimum cavity depth and avoid compressing insulation against the speaker |
| 9 | Fire-rated acoustic ceiling speaker | Multi-unit housing, hotels, offices, and fire-compartment ceilings | 6.5–8 in full-range driver | 20–60 W RMS per speaker | 8 ohms or 70/100 V, depending on configuration | Approximately 60 Hz–18 kHz | Cutout: 7.5–10 in; depth: 4–8 in including enclosure | Use fire-rated cable and connectors where required by the building specification | Maintain the ceiling’s acoustic and fire separation after cutting the opening | Use only assemblies tested for the required fire-resistance rating and have them inspected when necessary |
| 10 | Directional premium ceiling speaker | Focused music listening, boardrooms, galleries, and premium media rooms | 6.5–8 in woofer with adjustable tweeter | 50–120 W RMS per speaker | Usually 8 ohms | Approximately 40 Hz–20 kHz | Cutout: 8–10.5 in; depth: 4–7 in | 14–16 AWG cable for higher output and longer cable distances | Orient the adjustable driver toward the primary listening zone and keep pairs symmetrical | Use an amplifier with stable impedance handling and calibrate levels after installation |
08045479132
Send Inquiry
Send Inquiry
Send SMS
